Joined in 2023 
82 
63 About this deal
I have a very old HP Jetdirect print server device that absolutely refuses to connect to the NanoHD AP. It connects to my Peplink Max Transit AP with no problem but for other reasons that you’ve helped me with, I don’t want to leave the router AP on, so I’ve hardwired it. I would really like to have all devices on the NanoHD APs so that my clients are all showing up in the Unifi Controller. Are there little known secrets for getting legacy devices to connect to Unifi APs? Thanks.
We have two UAP-AC-LR indoor and looking for the best option to extend outdoors (to ensure coverage on the terrasse) the wireless network. We have one constrain though – an Ethernet connection to neither the AP nor the router is possible. It is my understanding that adding a UAP-AC-PRO to the current setup (provided a wireless connection to one of the existing AP) could help us achieve the goal. Could you please confirm or maybe suggest a better alternative? Thank you. Basically I use my computer and my smart tv hooked up right now only to my edgerouter 4 max this product
Versatile Design
I just had a similar issue with an old iphone 4. What ended up working for me was creating a second wireless network where i set the ‘Combine Name/SSID’ field to off, so there was a different ssid for the 2.4 and 5ghz networks. The iphone was able to connect to that. The last access points that we are going to take a look at in the UniFi AP comparison are the high density and enterprise models. Just to add clarity. The new home is wired ethernet to all rooms and provision for one access point connection in each of the two floors. We are thinking to add a unmanaged switch after the ISP provided modem/router. Connect two access points. I hope this post helped you to reset Unifi AP to its factory defaults and then you can adapt it again in your controller.
how the U6 Pro 2.4 GHz perf can be so good (573.5 Mbps) whereas U6 lite is also using 2×2 MIMO and only reaches 300Mbps ? Bandwidth steering helps dual-band clients, like laptops, mobile phones, tablets, etc. to use to less-congested and higher capacity, 5 GHz band. This will result in better WiFi performance for those devices. You can enable and configure bandwidth steering per device in the Unifi Controller.I then connected my Unifi Gateway Pro secondary WAN port to my LAN and configured the secondary WAN port to point the the 192.168.3.1 router.
I would like to leave the Peplink AP on but I’m wondering the ramifications. Will a device carried from my office to my main house stay connected?
Long-Range Ethernet Repeater
PS we have a close friend with intimate knowledge of CLI, SSH, etc, but who does not know much about physical networks. Any software-based interventions should therefore not pose any problem, as long as we know where to start and what to expect.
Hi Ruud, thanks for the interesting article. I was wondering how you think about the fast roaming option? Should i enable it for better performance? Thanks for answering! But make sure that that the wireless network signal strength is strong enough where you place the beacon. Because if you BeaconHD has a poor connection, then the clients downstream won’t benefit at all.
Standard 24 PoE
Make sure that you have Java11 JRE installed on your device. If you don’t have it installed, then the installation will warn you about it. Step 3 – Install Unifi Controller Ubiquiti makes in my opinion the best access points that you can buy these days. They offer a wide variety of Access Points (AP) in their UniFi product line that gives you the best value for money. But which access point should you buy? I am going to help you with the comparison of the different models. Dedicated hardware offload for QoS, Guest Control, and client management ensures high throughput and reduced latency. Unifi SDH – UAP-AC-SHD I have UAP-AC-PRO devices running in two separate houses. Can I configure them on the same UniFi controller or do they have to be separate? If separate how do i go about doing that.
Great Deal 
New Comment